Order of Assembly

is important.

Need I say more?

I hadn't expected installing the laundry chute to be simple, so let's buckle down to work.

First, the hole.  You can see the 2 x 4 the chute was resting on in that picture above.  And if you look especially carefully you can see a small wedge of the steel support column sticking out from under it.

You don't have to look carefully at all to see the mess in the basement.

Here is that column.  The bent corner to the left is the one in the way.

Same corner, one reciprocating saw minute later.  That steel might have been 1/8" thick, but it wasn't hardened so it sliced like butter.

Now lets make a hole in the hall wall.

Marked

Cut

From the other side

We knew from that very first photograph that sheetrock would have to give, so lets get on with it.

I didn't even get to finish the sheetrock before damaging it!

Closer.  Still hung up on something.

There is the problem.  Wedged tight against the subfloor above.

A little coaxing with the recip saw later...

Ready for trim.

Ready for a cascade of clothes.  It shouldn't back up until the laundry pile is six feet high.

Patch the not-yet complete sheetrock.

As good as new.  Or at least it will be after six more coats of mud.

Cabinets!

We finished assembling all the cabinets!  It made a world of difference to have Dad helping me.  I couldn't have assembled most of them without assistance.

Sink base cabinets for girls' bathroom.

 Notice the "dent" in the left hand one to go around the laundry chute.

Wall of cabinets for girls' bathroom

The bottom sections will have four drawers each (who ever heard of 16 drawers in a bathroom!).  The cubes will be open cubbies for the girls to put their stuff while getting ready.  No need to put clothes on the floor or counter!  The top sections will have shelves and—get this—doors.  We can stores stacks of towels without their tumbling onto the floor, and our guests won't have to see our cleaning supplies.

Cabinets for corner where sink was

The bottom section is a cabinet with two drawers (yes, 2 more).  Plenty of room for TP and whatever else is needed near the toilet.  Once again the center cubes are open.  Someplace other than the back of the loo to put those PJs while showering.  And the top section is shelves with doors.  Think "towels near the shower".

Flycatcher Nest

A pair of flycatchers decided to nest over our front porch while you were gone. The nest appears to be made from mud and moss. If you look very carefully in this picture you can see several little beaks pointing up.

Some Assembly Required

This morning I finished the first smoothing coat on all the sheetrock, but our real focus was on cabinets since that goes so much faster with two people.

Here is the proof that we ran a saw most of the day:

Perspective aids any cause.

Dad and I did finish all the cuts about 7 pm tonight.  Do you like my nice, neat stack?

We still had a little energy so we got started on the assembly.  We put together the laundry chute, the boys' vanity, and two of the pieces that go in the corner where the girls' sink used to be.

Tomorrow we will try to assemble the other ten units before Dad has to leave.

Progress Report

Just a small update today. We concentrated on the sheetrock and have all the seams taped except for one corner in the boys' bath.

See how nice the skylight looks?

Progress with Dad's Help

Dad and I have been working hard in the evenings.  We are focusing on cutting plywood for the cabinets while it is still light outside, and then after a bite to eat we work on mudding.

Here are the cabinets so far:

I know, they don't look like much.  That is about a third of the pieces we need.

Last night Dad just spotted the screws, but tonight he had to learn to tape corners since there are so many to do.  We are about halfway done with the seams.  I'd love to have them done, but half isn't bad for only two hours of work.

Dad has also been working on cabinets during the day.  These are the door fronts for the bunny boxes.  The lighter-brown ones in the back are the paper trays for the school room.  I can't wait to get that plastic thing off the counter!

Dad mounted the guides on all the drawers in the girls' room:

We decided we need to buy additional guides for those huge drawers at the bottom.  I'll order those when I order drawers for the bathrooms.

Doesn't your room look better with all that stuff moved back out, Eleanor?

Maybe not all that exciting.  We only have a few hours of serious productivity in the evenings, and the big change—installing the cabinets—has many hours of work before there is anything to see.

Shades of Sheetrock

Today was sheetrock day!

Angela came over to help, and I doubt I could have done the ceiling without her.  It was great having someone to call out measurements, hold the other end of panels, and hand me all the tools I kept leaving in the wrong place.  She had to leave in the mid-afternoon, but by then all the ceiling was up (not including the skylight) and several important stretches of wall.  Plus she helped me move another load of sheetrock in from the car.

The boys' bathroom is completely rocked:

The girls bathroom is about 80% rocked.  I only have half the wall behind the toilet, the wall to the right of that, the wall behind the sinks, and the half-wall to the left of that.  I think I need to put the laundry chute before doing those last bits, so I plan to build and install that tomorrow.

Now you can admire the skylight:

Look at those trapezoids and guess how many trips up and down the ladder each one took.

WRONG!  They only took two each: one to make a paper template and one to install the finished piece!  I had a complete brainwave as I was about to start and thought, "There is no way in the world to measure those but if I could only trace the pattern on a big sheet of paper I could get the right the first time."  The roll of construction paper was right there, so a few staple and pencil marks later I had perfect templates.  And it was a very good thing, too, because the two sides actually have some curve to them because of the geometry.  It would have been impossible to check where the piece needed to be trimmed.  You had to start with a piece that fit and gradually curve it around to the final shape as you installed the screws.